Quick answer
A mainstream stand-up snack pouch is a three-web laminate: a printed PET or OPP outer film, a metallised barrier film (or, for longer shelf life, aluminium foil), and a PE sealant, usually about 100 µm in total. A press-to-close zipper and a folded base gusset turn it into a pack that stands, reseals and runs on pouch or form-fill-seal lines. Real packs vary by brand, market and fill weight, so treat every range below as a typical figure, not a specification.
This piece rests mainly on pouch converters’ and film suppliers’ own pages (for example YLT Packing, Mondi and Enviroflex, all of which sell pouches or films). Independent data from CEFLEX, The Recycling Partnership and the Association of Plastic Recyclers is used for the recycling section. Nothing here comes from opening or measuring a pack.
What it is for
A snack pouch has to keep three things out: oxygen, which stales fried and baked snacks, moisture, which kills crunch, and light, which degrades oils and flavour. Aropack, a UK flexible packaging supplier, lists targets for dry snacks of an oxygen transmission rate below 2 cm³/(m² day) and a water vapour transmission rate below 1 g/(m² day), for a shelf life of 6 to 12 months. It names OPP / metallised OPP / PE or PET / metallised PET / PE as the matching structures.
It also has to stand on a shelf, survive distribution without pinholes, seal reliably at line speed and, for a zipper pouch, reclose after the first opening. The pack is thin, so most of the job is done by layer choice rather than by wall thickness.
Typical construction
Laminate structures are written outer layer first and sealant last, with thickness in micrometres. The commonly cited workhorse, according to YLT Packing, is PET 12 µm / metallised PET 12 µm / PE 80 µm for barrier-sensitive dry goods, with PET 12 µm / aluminium foil 7 µm / PE 80 µm taking over when shelf life needs to exceed 12 months. The same supplier says a stand-up pouch is a laminated bag with a folded gusset in its base.
| Part | Typical material | Typical thickness or size | Named source |
|---|---|---|---|
| Outer web (carries the print) | PET, or matt OPP for a soft-touch look | 12 to 25 µm for PET | GCL Packing |
| Barrier layer | Metallised PET or metallised BOPP; aluminium foil for longer life | 12 µm metallised PET; 7 µm foil; 15 to 20 µm metallised BOPP | YLT Packing; CloudFilm |
| Inner wall and sealant | PE | 80 µm in the structure above; 90 to 100 µm on 1 kg pouches | YLT Packing |
| Whole wall | Laminate of the above | 60 to 130 µm for snack pouches; 100 µm cited as a typical retail spec | YLT Packing; BS Flexpack |
| Closure | Press-to-close zipper | 13 mm zipper, 30 to 35 mm from the top | BS Flexpack |
| Seals and opening | Heat seals on sides and base; tear notch | Seal width 7 to 9 mm; notch 15 mm from the top | BS Flexpack |
| Roto (gravure) or flexo ink on the outer web, no separate label | Ink weight not found in public sources | Mondi (print methods) |
Kraft paper is also sold as an outer layer, at 30 to 50 g/m² according to PackagingBest, though it still sits on a barrier film inside. Mondi lists roto and flexo printing for its PE-based pouch, which is where the print row comes from.

Source: YLT Packing, Food Packaging Pouch Materials guide (supplier reference structures, typical not specification)
The chart shows the layer thicknesses from YLT Packing’s two reference structures. Our calculation: in PET 12 / metallised PET 12 / PE 80, the sealant is 80 ÷ (12 + 12 + 80) = 80 ÷ 104 = 77 percent of the film stack. Swap in 7 µm foil and the stack is 99 µm, with PE at 81 percent. YLT’s own table lists about 115 µm for a stack whose layers add to 104 µm, so adhesives, ink and tolerance may account for roughly 11 µm; that gap is our inference from one row, not a published figure.
Free tool: the laminate estimator gives an indicative layer-stack weight and barrier from your own layer thicknesses.
Why it is made this way
Barrier
Each layer has one main job. The PET outer web gives stiffness, print quality and heat resistance during sealing. YLT’s guidance is to keep a stiff outer web and avoid over-thick soft sealants that make the pack slump, which explains why the outer film is not simply thinned down.
The metallised film supplies most of the barrier. Aropack gives typical figures per 25 µm film of 0.5 to 1.5 cm³/(m² day) oxygen transmission for metallised PET and 50 to 100 for metallised OPP. Poly Print, citing ExxonMobil-type data, gives a wider range for metallised OPP of 19 to 160 cm³/(m² day) at 23 °C and 0 percent RH. The two sources use different test bases and grades, and these are typical values, not specifications; check that any supplier quotes ASTM D3985 for oxygen and ASTM F1249 for water vapour at stated temperature, humidity and thickness.
That gap is why metallised OPP is often used where moisture and light matter most and oxygen is less critical, and metallised PET where fat oxidation sets the shelf life. Foil sits above both: YLT says PET/AL/PE gives the strongest light and oxygen protection, and PackagingBest says foil costs more but extends shelf life significantly. Ask your supplier for a quote rather than relying on that general statement.
Strength, filling and seals
The sealant carries the seal. YLT notes that on a 1 kg pouch the 90 to 100 µm sealant layer carries most of the seal strength requirement. Pouches arrive at the filler either pre-made or as film for form-fill-seal; Mondi, for example, supplies its mono-material pouch as FFS material and as a pre-made stand-up pouch.
Cost follows from these choices. A thicker sealant, a foil layer or an extra film adds material and a lamination pass, while a thinner total wall saves resin but narrows the margin on puncture and seal integrity. The lightweighting calculator is on this site if you want to size that trade, but it is a fourth tool link beyond our limit for this piece, so use the unit converter below for mil-to-micrometre checks first.
Free tool: the unit converter handles gsm, microns and gauge when suppliers mix units. Enviroflex, for example, lists 4.8 mil against 5.4 mil for standard laminates; at 25.4 µm per mil that is about 122 µm and 137 µm.
How it is recycled today and what is changing
A PET / metallised film / PE laminate is a multi-material structure, and it is a poor fit for mechanical recycling. ETC/CE’s 2022 report says only clean or cleaned PE and PP flexible packaging is currently recycled on an industrial scale in Europe. In the US, The Recycling Partnership puts the residential recycling rate for film and flexible packaging at about 2 percent, and the APR says flexible plastics can jam MRF sorting machines, so pouches go to store drop-off, which accounts for about 20 percent by weight of recovered film.
The design response is mono-material polyolefin. CEFLEX’s D4ACE guidelines require at least 90 percent of the functional unit to be the target mono-material for plastic-based consumer flexibles, and CEFLEX estimates 50 to 60 percent of the 8.4 million tonnes of European consumer flexibles per year are already mono-PE, mono-PP or mixed polyolefin (as of its September 2025 summary). Collection and sorting capacity, not film design, is what CEFLEX says remains the limit.
EU rules on recyclability grading and design for recycling are set under the Packaging and Packaging Waste Regulation (PPWR); check the current text at ppwreu.org before putting any claim on a pack.
Alternatives being tried
All of the following are supplier or brand claims as of 10 November 2026; none has been independently verified for this article.
- Mono-PE or mono-PP pouches. Mondi says its re/cycle StandUpPouch is certified recyclable with up to an AAA rating (above 95 percent) and is lighter and stronger than PET/PE laminates of the same thickness. Its PE version can include EVOH for barrier. Aropack adds that mono-PE with EVOH interlayers below the 5 percent weight threshold can reach under 1 cm³/(m² day).
- Coated mono-PP with in-line barrier ink. Siegwerk and Enplater announced a mono-PP pouch on 30 April 2026 that uses an oxygen-barrier white ink applied in one step. The pouch was shown at Interpack 2026, with protein chips among the demonstration packs.
- Paper-based pouches. Mondi offers paper-based stand-up pouches for confectionery and snacks built on FunctionalBarrier Paper 95/5. In the UK, The British Crisp Co. says its metallised-paper packet was certified recyclable in standard paper mills by OPRL, and describes it as the first fully recyclable crisp packet. SPS Pouches, a pouch seller, notes that kraft pouches with under 15 percent plastic count as kerbside recyclable under OPRL, with that limit under review.
What this means for you
- If you buy pouches, ask for the layer stack in writing, in the notation above, with thickness per layer and the test conditions behind any OTR or WVTR number. Compare quotes at the same conditions and thickness.
- If you are moving to mono-PE or mono-PP, run shelf-life trials on your own product first. Barrier numbers from a data sheet do not transfer to your fill, fat level or distribution.
- Check zipper, valve and ink choices against the same recycling guideline as the film, since the 90 percent rule in D4ACE applies to the whole functional unit.
- Treat recycling claims as market-specific. A pouch that is accepted at US store drop-off may have no collection in the UK or EU, so check the local scheme and the current PPWR text before claiming anything.
Sources
- YLT Packing: Food Packaging Pouch Materials, Films and Barrier Guide
- YLT Packing: Custom Snack Packaging Pouches, A Complete Guide
- YLT Packing: Stand Up Pouch, What It Is and Which Products Suit It
- GCL Packing: Stand Up Pouch Materials, How to Choose the Right Structure
- PackagingBest: Stand Up Pouch Materials, PET, Foil, PE
- BS Flexpack: Stand Up Pouch Material Determines How Well Your Product Is Protected
- CloudFilm: Metallized BOPP Film
- Aropack: How to Specify Barrier Performance for Flexible Food Packaging
- Poly Print: Oxygen Transmission Rate
- Mondi: Mono-material barrier packaging
- Mondi: Mono-material StandUpPouch
- Mondi: Paper-based StandUpPouch
- Enviroflex: Recyclable Stand Up Pouch 8 oz
- CEFLEX: Designing for a Circular Economy, Executive Summary, September 2025
- CEFLEX: The critical role of circular economy guidelines
- ETC CE: Flexible plastics in Europe’s circular economy (2022)
- The Recycling Partnership: Addressing the Challenge of Film and Flexible Packaging
- Association of Plastic Recyclers: Are you recycling your bag full of bags?
- Packaging Strategies: Siegwerk and Enplater Develop Fully Recyclable Mono-PP Pouch
- Nissha Metallizing Solutions: The British Crisp Co. launches recyclable potato chips packet
- SPS Pouches: Why the flexible packaging industry is moving towards mono-materials
This is desk research from the cited sources, not a physical teardown. Real packs vary by brand and market.
Header image: illustration, AI-generated.

