Wet pet food pouches: the mono-PP retort lesson for FMCG

Quick answer: A wet pet food pouch has to survive sterilisation at around 121 to 135 °C, which is why foil laminates have been hard to replace in this format. Mars announced on 10 November 2026 that it will install new pouch lines at Melton Mowbray for mono-PP packaging, and the construction options converters describe show what any heat-treated or oxygen-sensitive FMCG pack faces when it goes single-material.

This piece rests mainly on Mars statements, trade press and converters’ own product pages; independent test data on retort mono-PP is thin, and the barrier figures below are suppliers’ claims.

What Mars has announced, and what it hasn’t

According to Mars’s press release of 10 November 2026, the £161 million investment at Melton Mowbray covers smart optical sorting, which Mars says will cut production waste by over 50%, and pouch lines that enable a switch to fully recyclable mono-PP. The Manufacturer reports that the programme runs to 2031 and will make the site Mars’s primary UK factory for pouched pet food.

The pack itself is not new. In July 2025 Mars launched a “designed to be recyclable” mono-PP pouch for Whiskas in the UK and Germany, and said the switch cut the packaging’s carbon footprint by 46%. Mars hasn’t published the layer structure, thicknesses or barrier values in the sources I found, so everything below describes the category rather than that pack.

Mars isn’t alone in wanting this. Pet Food Processing reports Mondi’s RetortPouch Recyclable as a mono-material, high-barrier film for retort, aimed at wet pet food and similar human foods. Packaging World covered ProAmpac’s RT-3000, with the company stating it withstands 130 °C retort conditions.

Why retort is the hard case

Packaging World’s account of the ProAmpac launch makes the core problem plain: polyethylene, the usual recyclable pouch polymer, isn’t suited to products that need around 130 °C, so pet food makers fell back on mixed-material pouches that don’t recycle. A converter’s guide quotes maximum process temperatures of about 50 °C for PE and about 95 °C for PP in typical mono-material pouches, which is why YLT Packing’s structure guide puts conventional laminates alone at retort level.

The conventional pouch is a three- or four-layer laminate. Packaura’s layer guide describes about 12 µm of PET outside, 9 to 18 µm of aluminium foil, and 70 to 80 µm of cast polypropylene (CPP) as the food-contact seal layer, for roughly 100 to 120 µm in total. Four-layer versions add oriented nylon for puncture resistance, and Logos Endiri gives the foil as 7 to 9 µm and quotes an OTR below 1 cm3/(m2 day) for it, without stating test conditions.

Our calculation: using Packaura’s figures, foil is 9/120 = 7.5% of laminate thickness at the thin end and 18/100 = 18% at the thick end. Thickness isn’t weight, but it shows that the layer blocking recycling is a small fraction of the structure, and the sealant does most of the volume.

That sealant detail matters for the switch. The sealant layer of the foil pouch is already polypropylene, so mono-PP keeps the part that survives heat and replaces the foil, the nylon and the PET print layer.

What replaces the foil

Converters describe two routes. The first is a coated PP film: Bowe describes OPP/HBOPP/RCPP, where the high-barrier layer is a SiOx coating on oriented PP, and quotes OTR of 0.5 or below and WVTR of 0.5 or below (units given as ml/(m2 24 h 0.1 MPa) and g/(m2 24 h), test conditions not stated). Qiyu quotes OTR of 0.1 to 0.5 cc/(m2 day) for a similar BOPP/high-barrier OPP/RCPP structure at 121 °C for 30 minutes.

The second is a thin EVOH layer inside the PP. Achievepack says plain mono-PP is a weak gas barrier (it quotes 1,000 to 2,000 cc/m2 per 24 hours, conditions not given) and that adding under 5% EVOH by weight keeps PP above 95%. EVOH loses oxygen barrier as it absorbs water; Aropack notes it must be protected, often sandwiched between polyolefins, and retort is the wettest, hottest place to test that.

One converter, LD Pack, describes a retort pouch of at least 90% mono-PP with no metallised layer, rated 121 °C for 30 minutes. Note the “at least 90%” wording, which is looser than the 95% figure above; recycling schemes define their own thresholds, so ask which one applies.

Comparing the formats

Structure Retort range (°C) Oxygen barrier (supplier claim) Recycling stream Main trade-off
PET/Al/CPP (foil) 121 to 135 Below 1 cm3/(m2 day), conditions not stated (Logos Endiri) Mixed material, not mono Foil barrier; hard to recycle
PET/NY/RCPP (no foil) 121 to 128 Rated “good” by YLT Packing, no figure Mixed material Puncture resistance; lower barrier than foil
OPP/HBOPP/RCPP (SiOx) 121 (Bowe, Qiyu) 0.1 to 0.5 (Qiyu, cc/(m2 day)) PP Coating must survive retort and flexing
PP with under 5% EVOH Converter-dependent No figure given PP EVOH needs moisture protection
Mono-PE Not for retort (ProAmpac) No figure given PE Not for retort

Ask any supplier for OTR at 23 °C and a stated humidity (ASTM D3985) and WVTR at 38 °C and 90% RH (ASTM F1249), measured after retort, not on the virgin film.

Why it matters for other categories

Retort is the extreme, but the same logic applies wherever a pack is heated or sold on a long shelf life. Mondi’s pitch, per Pet Food Processing, explicitly extends to similar human food, so ready meals sit in the same design space. The trade-off is always barrier, heat tolerance and recyclability, and you rarely get all three at the foil level.

Smithers frames the wider shift. In its report for Packaging Innovations & Empack 2027, covered by Packaging News on 19 November 2026, mono-material structures account for 81% of flexible plastic packaging and are expected to grow faster than multi-material ones to 2031. The same report names Extended Producer Responsibility and the EU Packaging and Packaging Waste Regulation as drivers of format and material choice; for the legal detail, see ppwreu.org and check the current text.

Pet food adds a commercial lesson: Mars is changing the line, not only the film. Retail Gazette reports that the shift will require change across the infrastructure supporting products from manufacturing to retail, and Mars’s investment is spread over a programme to 2031. A film swap that needs new pouch-making and filling lines is a capital project, not a specification change.

What this means for you

  • R&D: separate the three jobs (print surface, barrier, seal) and ask which one the new structure does worse. Request barrier data after your actual process, not on the roll, and note that EVOH and coatings behave differently once wet or flexed.
  • Procurement: converters quote different mono-PP definitions (above 90% or above 95% PP). Write the definition and the recycling scheme you are targeting into the specification, and ask your supplier for a quote on a full structure, not on a film.
  • Design: PP has a different touch and print behaviour from PET, as LD Pack’s own page admits. Plan proofing time for the outer layer.
  • Operations: ask whether your fillers and sealers can run the new film at line speed. Mars’s choice to install new pouch lines suggests this can’t be assumed.
  • Claims: Mars uses “designed to be recyclable” and ties it to existing or emerging infrastructure. That is a narrower statement than “recyclable”, and worth copying in wording.

Free tool: the laminate estimator gives an indicative weight and barrier for a layer stack, which helps compare a foil laminate with a mono-PP stack before you ask for samples. Free tool: the unit converter handles micron to gsm conversions when suppliers quote in different units.

Sources

Header image: illustration, AI-generated.