Quick answer: Pet food pushed flexible packaging into recyclable mono-material pouches earlier and harder than most other food categories, because the bags are big, the fat content is high, and the shelf-appeal pressure is intense. The current best compromise for dry food is a mono-PE pouch with a thin EVOH or coated barrier layer; wet, retorted pet food still mostly needs foil. Both points carry lessons for anyone specifying flexible packs in food, home care or personal care.
Why pet food got there first
Pouches already dominate pet food packaging by format. In 2024, pouches held a dominant position in the pet food packaging market by product type, capturing more than a 39.2% share, with growth driven by their lightweight nature, cost efficiency, and convenience features such as resealability and easy storage. A separate analysis puts the figure higher still: by product type, pouches held 43% revenue share of the pet food packaging market in 2024. The exact number depends on who’s counting, but the direction is the same.
Within materials, flexible plastic leads too. The flexible plastics segment accounted for USD 4.71 billion in 2025, making it the largest material category, with growth driven by rising demand for recyclable flexible plastics due to government mandates and circular economy policies. That combination of scale, fat content and a loud sustainability narrative from pet-care brands is why converters tested mono-material barrier film on dog kibble bags well before they tried it on, say, savoury snacks.
Two pouch families, two different problems
Pet food packaging splits into two structural traditions that solve different problems. Dry food bags need oxygen, moisture and grease barrier over months on a shelf. Wet food in retort pouches needs to survive sterilisation at high temperature, so the laminate has to hold its seal and its barrier through a cook cycle, not just sit quietly in a warehouse.
Traditional dry-food bags and retort pouches both leaned on multi-material laminates built around PET, aluminium foil or metallised film, and a polyolefin sealant. As one industry explainer on the shift away from that structure puts it, packaging manufacturers have traditionally utilized multi-material structures with a metallized layer, which on top of barrier properties tend to maintain the structural integrity of the pack. The catch is recyclability: those structures mix polymer families that mechanical recycling streams can’t separate.
The table below sets out the main structures still in use, with typical barrier figures reported by converters. These are typical values from supplier and converter literature, not certified specifications, and the oxygen transmission rate (OTR) depends on test method, temperature and humidity, which the sources below do not always state in full.
| Structure | Typical build | OTR, cc/m²/day | Recyclability | Best fit |
|---|---|---|---|---|
| Foil laminate | PET / aluminium foil / PE or CPP | <0.1 | Not recyclable in most systems | Retort wet food, long ambient shelf life |
| Metallised laminate | PET / metallised PET / PE | 0.5 to 2 | Not recyclable in most systems | Mid-tier dry food and treats |
| Mono-PE with EVOH | PE / EVOH / PE co-extrusion | 1 to 5 | Designed for PE recycling streams | Large dry kibble bags, 3 kg and up |
| Mono-PE or PP, no EVOH | Single polymer family | Moderate, not usually quoted below 5 | Most recyclable option | Biscuits, treats, short shelf life |
The pattern holds across sources: foil structures give the tightest barrier, while mono-PE with EVOH trades some performance for easier recycling. A separate converter guide gives a tighter benchmark for the mono-PE/EVOH family, stating that co-extruded PE/EVOH/PE mono-material structures achieve oxygen transmission rates as low as 0.5 ml/(m²·24h·0.1MPa), which is the threshold that keeps dry kibble, treats, and toppers fresh through a typical retail shelf life. That figure uses a different unit convention (per 0.1 MPa pressure differential) than the cc/m²/day figures above, which is a reminder to always check the test method before comparing two suppliers’ barrier claims directly.

What mono-material actually gives up
Mondi’s re/cycle FlexiBag, developed with French pet food maker Saga Nutrition, is the clearest named example of the dry-food switch. Mondi has worked with Saga Nutrition to develop mono-material dry pet food packaging that balances a recyclable design with high-barrier protection, replacing non-recyclable, multi-material plastics and aligning with CEFLEX’s recycling guidelines. The pack comes at a minimum size of 3kg and claims to protect products against moisture, fat, and odour with its high-barrier properties. The 3 kg floor matters: it tells you the structure works at the scale and headspace of a large dry-food bag, which is not automatically the case for a 400g retail pouch with far more surface area relative to volume.
At the small end, a Brazilian converter’s project for pet treat brand Adimax shows the opposite constraint. Plastrela collaborated with ExxonMobil to create a snack size pet food standup pouch that replaced a conventional multi-layer PET/PE structure with a mono-material PE//PE solution that could be easier to recycle. The technical headache wasn’t barrier, it was machinability: the biggest challenge in changing from a transparent PET structure laminated with PE film into a PE//PE structure was the formatting and machinability of the film in the cutting-welding equipment, because SUP production typically needs a high sealing temperature that historically meant using polyester film.
Coatings are a third route. Siegwerk, working with Windmöller & Hölscher and B&B, applied functional barrier coatings to a mono-PE dry pet food bag rather than co-extruding EVOH into the film. Siegwerk’s inline printable grease barrier coating and a heat-resistance coating have been applied to a mono-PE bag, which keeps the structure within a single resin family while still printed inline on standard flexo or gravure equipment.
All three approaches sit inside the same recycling guardrail. CEFLEX, the industry body behind EU flexible-packaging recyclability guidance, limits how much non-PE barrier material a mono-PE structure can carry. CEFLEX guidelines cap EVOH at roughly 5% of total structure weight for PE film to remain mechanically recyclable, which is the ceiling every converter above is designing against.
What wet, retorted food still can’t give up
None of this applies cleanly to retort pouches for wet pet food, which have to survive sterilisation at high temperature and still hold their barrier. The structures are different and more complex. Typical three-layer retort builds use PET/AL/CPP, where PET provides mechanical strength, aluminium blocks light and oxygen, and CPP seals; four-layer builds add nylon (PA) for puncture resistance on bone-in wet food. Retort runs at 121°C for 45 minutes in some documented converter specs, conditions that rule out most compostable or lower-melt-point recyclable films.
Foil isn’t a small line item in that structure either. The aluminium foil layer, often imported for pinhole resistance and flatness, can drive raw material costs up to 60% of total production. That’s a cost-share fact, not a price quote, but it explains why removing foil from retort pouches is a much bigger redesign than swapping a dry-food bag to mono-PE: the foil is doing structural and economic heavy lifting that a PE/EVOH film can’t yet replicate at retort temperatures.
Wikipedia’s summary of the format is blunt about the consequence: the multi-layer structure prevents the retort pouch from being recycled into other retort pouches or food packaging, though the material can be recycled into an aluminised resin or up-cycled into textile materials. For wet pet food, ready meals and similar high-temperature-processed FMCG packs, foil is likely to stay the default barrier solution for a while yet.
Where the lesson crosses into other FMCG categories
The same tension between barrier and recyclability shows up wherever a dry, fat-sensitive or aroma-sensitive product needs a long shelf life: coffee, savoury snacks, some supplement powders and baby-food formula. Coffee is the clearest parallel already in the market. One converter marketing a recyclable mono-PE pouch notes that European coffee roasters preparing for PPWR replacement specify the high barrier PE pouch to retain aroma, oxygen, and moisture protection, the same mono-PE-plus-coating or mono-PE-plus-EVOH logic pet food converters have been running for several years.
The practical lesson for a packaging engineer outside pet food is less about copying a specific film structure and more about copying the sequencing: start with the largest, least fussy SKU in the range (pet food started at 3 kg dry bags), prove the mono-material structure holds barrier and machinability there, then work down to smaller formats where seal temperature and surface-to-volume ratio make the swap harder. Trying to convert the smallest, highest-barrier SKU first is the route that stalls projects.
It’s also worth separating marketing claims from recyclability claims. A pouch that is “designed for” or “compatible with” PE recycling streams is not automatically accepted at every kerbside or store drop-off programme; actual recyclability depends on collection infrastructure in the market where the pack is sold, and on meeting published guidelines rather than just using the right resin family. This is an area where EU packaging and packaging waste rules are in active revision, so check the current text at ppwreu.org before making a recyclability claim on-pack.
What this means for you
- R&D and quality: before swapping a foil or metallised laminate for mono-PE, run real shelf-life trials against your actual fat, moisture and oxygen-sensitivity profile. The OTR ranges in the table above span a factor of 50, and the test conditions behind any single number matter more than the headline figure.
- Design: if the pack has a wide barrier range to choose from, model the layer stack and weight trade-off before committing to a converter trial. The laminate estimator gives an indicative read on barrier and weight for a given layer stack.
- Procurement: ask any converter proposing a mono-material swap for their CEFLEX or equivalent recyclability documentation, not just a claim that the pack is “recyclable.” Ask specifically what percentage of the structure, by weight, is EVOH or coating, since that is the figure recyclability guidelines actually cap.
- Format strategy: if your range spans multiple pack sizes, expect the mono-material swap to work first on your largest, bulkiest SKU and to need separate development for smaller or more delicate formats, exactly as it has in pet food.
- Retort and high-temperature processes: don’t assume a mono-PE success story elsewhere in your portfolio transfers to anything that needs sterilisation. Foil-based retort structures remain the practical default for high-temperature processing for now.
- For a general reference on material properties across packaging formats, the material properties table is a useful starting point when briefing a converter.
Sources
- Packaging Europe: Siegwerk prints mono-PE pet food bag with recyclable barrier coatings
- Packaging Strategies: Plastrela creates recyclable mono-material polyethylene pet food standup pouch
- Plastics Today: Extrusion technology enables sustainable pet food packaging
- YLT Packing: Custom pet food bags, styles, barrier films and printing
- LD Pack: Retort pouches for wet pet food
- Wikipedia: Retort pouch
- SPEXPACK: Custom retort pouches
- Packaging Europe: Saga Nutrition implements Mondi’s recyclable, mono-material pet food pack
- Mondi Group: Happier pets, smarter packaging, Mondi and Saga Nutrition launch sustainable solution
- Packaura: Eco-friendly pet food packaging, materials and PPWR guide
- PouchEco: High barrier PE pouches, recyclable pouches for Europe
- Impacked: Pet food packaging bags for brands, low-MOQ guide
- Global Market Insights: Pet food packaging market size and share report
- Market.us: Pet food packaging market size and share
- Mordor Intelligence: Pet food packaging market size and forecast

