How EPS, PUR and VIP insulation behave in cold chain shippers

Quick answer: insulation decides how fast heat gets into the payload, and the coolant decides which temperature the payload sits at. On published ranges, vacuum insulated panels (VIP) have the lowest thermal conductivity, PUR foam sits in the middle and EPS is highest, so VIP tends to be chosen where wall thickness or duration is the constraint and EPS where lanes are short. Only qualification testing of the complete pack-out shows what a given configuration does.

This piece rests mainly on supplier pages (Peli BioThermal, the VIP maker Super Tech, the box supplier Balaji Internationals), patent filings and standards bodies’ own descriptions. Independent test data is scarce and is flagged where it exists. It is education only: material and pack choice, and compliance for any product, are decided with your regulatory and quality teams and the applicable pharmacopoeia or authority.

What the three insulation types are

Super Tech describes EPS as expanded polystyrene beads fused together, with air-filled cells doing the insulating. The same VIP maker ranks EPS as having the lowest thermal resistance of the common options, which is a seller’s view of a competing material.

PUR shippers are made differently. According to a US patent filing on VIP sandwich shippers, a liquid PUR mix (isocyanate, polyol and other components) is added into a corrugated box and cured to foam. A related PUR patent adds that the foam can be made in different densities and hardnesses, so “PUR” is a family, not one number.

A VIP is a core sealed inside an impermeable sleeve under vacuum. A patent background section notes that the vacuum can be as strong as 1 mbar, which makes the panels susceptible to damage. The same filing adds that the vacuum is the main reason for the high R value, and a panel without it drops to about R4 per inch, similar to EPS.

The weak point is the assembly, not the panel. The VIP patent says that a typical VIP shipper joins five panels with tape or strapping, and that although individual panels may reach R40 per inch, the whole shipper may land at R25 to R30, a drop of 25 to 30 percent. That is a patent applicant’s claim about competing designs, so treat it as a reason to ask about edge treatment rather than as a measured industry figure.

Conductivity and hold time side by side

The ranges below come from Balaji Internationals’ insulated box guide. They are typical values, not specifications, and a supplier’s own data sheet for its grade will differ. The hold times are the same page’s indications for roughly 40 mm walls with gel packs against Indian summer ambient, so they are an illustration of ordering, not a design basis.

Insulation Thermal conductivity (W/(m K)) Indicative hold (h) Main trade-off
Moulded EPS 0.033 to 0.040 24 to 48 Bulky walls (20 to 50 mm), single-use in most formats
PUR foam 0.022 to 0.028 48 to 72 Foam grade and density vary; thinner than EPS for the same effect
VIP 0.004 to 0.008 Several days Vacuum loss, edge gaps and handling damage

Other sources give lower figures for the best panels. A patent background section cites 0.0015 to 0.0025 W/m K at the low end for VIP, which looks like a new, undamaged panel centre rather than a finished shipper. The Balaji page itself says PU panels give around 40 percent better insulation per millimetre and VIP shippers are confined to high-value biologics and returnable systems by cost. For price, ask your supplier for a quote.

Published thermal conductivity range by insulation type. Low end of range: EPS 0.033, PUR foam 0.022, VIP 0.004; High end of range: EPS 0.04, PUR foam 0.028, VIP 0.008 (W/(m K))
Published thermal conductivity range by insulation type
Source: Balaji Internationals insulated shipping box guide (supplier page, typical values, not specifications)

Our calculation. Using the table’s extremes, EPS at 0.040 divided by VIP at 0.004 gives a ratio of 10, while EPS at 0.033 divided by VIP at 0.008 gives about 4.1. So the spread is roughly 4 to 10 times lower conductivity for VIP, which sits next to Super Tech’s own claim of 3 to 10 times. At the midpoints (0.0365 and 0.006), a 40 mm EPS wall would be matched in steady-state conduction by 40 x 0.006 / 0.0365, about 6.6 mm of VIP, before edge losses and ageing.

Insulation is only half the stack, so the coolant matters just as much.

Coolants: gel packs, PCM and evaporative cooling

A water gel pack changes phase at 0 C. For a 2 to 8 C lane, one supplier explainer (Coldfront) says that this protects against heat but adds freeze risk, managed only through conditioning discipline and physical buffering. A patent on thermal management systems makes the same point, noting that water changes phase at 0 C, which may be too low for pharmaceutical products and can lead to freezing.

Phase change material (PCM) is formulated to melt at a chosen temperature. Coldchainer says a 2 to 8 C shipment typically runs a PCM that melts around 4 to 6 C. It also warns that a pack frozen well below its melting point pulls the payload colder than intended in the first hours of transit.

Coolant Phase point (C) Conditioning Main trade-off
Water gel pack About 0 Frozen, or conditioned and buffered Freeze risk to the payload if conditioned wrongly
Conditioned gel pack About 0 (held at 2 to 5 before packing) Pre-conditioned to 2 to 5 C Needs a controlled conditioning step and space
PCM brick or bottle About 5 for a 2 to 8 C band Conditioned to a defined state Usually costs more than gel packs, per Ecko Products Group
Evaporative cooling plus PCM PCM-dependent Activated at pack-out Proprietary systems, small payloads

Peli BioThermal’s NanoCool pages describe single-use shippers with evaporative cooling and on-demand conditioning that saves freezer space. The company lists 48 to 96 hours for 2 to 8 C and says the line is qualified to ISTA 7D profiles. These are manufacturer claims.

The payload’s own start temperature matters too. A supplier guide from Ecko points out that a room-temperature payload makes the refrigerant pull it down to 2 to 8 C and then hold it there.

Hold times are tied to ambient conditions

Rated hours always depend on the ambient. Peli BioThermal’s Crēdo Cube page lists a reusable shipper built from PCM and VIPs in sizes from 3 to 96 L, and gives 96 hours at 30 C to 156 hours at 20 C for the 2 to 8 C version. The same box, then, earns different ratings under different conditions.

Foam-based single-use formats appear on the same company’s product page. Its CoolGuard PCM line combines PCM with foam insulation for 2 to 25 C and 48 to 96 hours. A hold time quoted without its ambient, profile and payload mass is incomplete.

How shippers are qualified: ISTA and USP

ISTA’s thermal standards page presents 7E as heat and cold profiles built from real transport data, delivered with Standard 20 as a process standard. According to Temperpack, each 7E profile holds up to 72 hours of data that can repeat to 144 hours. The same source says the older 7D uses abrupt steps and holds, while 7E follows gradual daily swings.

Pelton Shepherd, a cold chain packaging supplier, says the profiles draw on data from 82 real-world shipping lanes. ISTA’s 7E overview adds a limit: the profiles are general simulations and are not meant to represent the worst-case thermal exposure.

On the pharmacopoeia side, an ECA Academy overview lists the USP <1079> series, including <1079.5> Qualification of Shipping Systems and <1079.6> Transport Route Profiling Qualification. SenseAnywhere notes these chapters are informational guidance, not enforceable requirements. For excursions, USP <1079.2> recommends a 24-hour window when calculating mean kinetic temperature for controlled cold temperature products.

In the EU, chapter 9 of the 2013 GDP guidelines says temperature-sensitive products should travel in qualified equipment such as thermal packaging. Check the current text for what applies to you. Packaging waste rules that touch single-use foam shippers are covered at ppwreu.org.

Questions for suppliers, regulatory and quality teams

For the supplier:

  • Which ambient, profile (7D, 7E or custom lane), payload mass and start temperature sit behind each rated hour figure?
  • For VIP: how are panels checked for vacuum loss, and how are edges and corners handled?
  • What are the pack-out and conditioning instructions, and what happens if a coolant is conditioned too cold or too warm?
  • For reusable formats: how many cycles and what service life are supported, and how is the return loop run?

For regulatory and quality:

  • What temperature limits and excursion allowances do the product’s labelling and stability data set?
  • Which lanes and seasons must be covered, and does the profile represent them?
  • How is a change to foam grade, coolant or panel supplier handled in change control?
  • How are monitoring data, excursions and returns of coolant documented?

What this means for you

Ask for the hold time with its conditions attached, then compare shippers at the same ambient and payload. A 96-hour label on one box and a 48-hour label on another may describe different tests.

Treat conductivity ranges as a way to shortlist. EPS is the starting point for short, cost-led lanes, PUR for mid-length lanes with limited space, and VIP where walls must be thin or duration long, as these suppliers describe it. Then pick the coolant by the phase point you need and check that your site can condition it.

Bulky walls cost warehouse and truck space. Free tool: the pallet load calculator shows how outer dimensions change cases per pallet.

Finally, confirm qualification evidence for the exact pack-out with your regulatory and quality teams, not the material name.

Sources

This article is general education about packaging materials, formats and test methods. It is not regulatory, quality or medical advice. For a real product, confirm material choice, testing and compliance with your regulatory and quality teams and the applicable pharmacopoeia and authority.

Header image: illustration, AI-generated.