Quick answer: For hard and semi-hard cheese, and for some chilled meat and ready meals, a thin film wrapped under vacuum can replace a formed tray. Sealed Air’s Cryovac range is the clearest published example: in its own trial, a 300 g cheese portion used 2.3 g of plastic in a trayless pack against 6.3 g in a selected thermoformed pack. The saving is real on paper, but it comes from one supplier’s comparison, so treat it as a starting point for your own trial.
This piece rests mainly on statements from Sealed Air, whose Cryovac brand makes the films and machines discussed, and on a Packaging Europe Spotlight written by a Cryovac executive. I found no independent test data for these packs, and I’ve marked where a figure is the supplier’s own. All dates and statuses are as of 3 November 2026.
What the trayless cheese pack actually changes
Sealed Air’s AutoWrap Lite is a horizontal form-fill-seal system. It wraps cheese in an ultra-thin film under vacuum, and the supplier lists the film as recycle-ready LDPE. The consumer units it covers run from 0.08 to 1.0 kg.
The weight comparison comes from Packaging Insights, quoting Carmen Roveda, EMEA director of sustainability and application for food at Sealed Air. In internal trials with a 300 g cheese portion, AutoWrap Lite packs used about 2.3 g of plastic, against about 6.3 g for selected conventional vacuum thermoformed packs. Roveda says the system eliminates longitudinal seals and air evacuation holes, which is where the tighter pack comes from.
Our calculation: 6.3 g minus 2.3 g is 4.0 g saved per pack, and 4.0 ÷ 6.3 = 0.635, so 63.5%, which matches the supplier’s figure. Over 1 million packs that is 4.0 g × 1,000,000 = 4,000 kg, or 4 tonnes of plastic. Per 100 g of cheese, the trial figures work out at 2.3 ÷ 3 = 0.77 g against 6.3 ÷ 3 = 2.1 g.
An earlier report gives a slightly different picture. When Sealed Air and Bradbury’s Cheese announced the system in November 2024, Packaging Europe reported about 2 g of material for 200 g of cheese and savings of up to 65%. That is 1.0 g per 100 g (2 ÷ 2). Pack size alone can move this per-100 g number, because a smaller pack carries proportionally more film.

Source: Sealed Air figures reported by Packaging Insights (2.3 g and 6.3 g per 300 g) and Packaging Europe (about 2 g per 200 g, Nov 2024); per-100 g values are our calculation
The chart shows plastic per 100 g of cheese. The two AutoWrap Lite bars and the thermoformed bar are derived from the figures above, so they are only as comparable as the packs behind them.
Four formats side by side
The table puts the formats Sealed Air describes next to a conventional thermoformed baseline. Weight and scrap claims are the supplier’s, and they are not measured against the same product, so don’t read across rows.
| Format | Typical use (per supplier) | Structure stated | Plastic or scrap claim | Trade-off |
|---|---|---|---|---|
| Conventional vacuum thermoformed pack | Baseline in the cheese trial | Formed bottom web plus lid | 6.3 g for 300 g cheese | Rigid shape; heaviest in this comparison |
| HFFS soft vacuum wrap (AutoWrap Lite) | Hard and semi-hard cheese, 80 to 1,000 g | Ultra-thin recycle-ready LDPE barrier film | 2.3 g for 300 g cheese | Not for active, gassing cheeses; soft pack |
| Flow-Vac shrink bag (PrimeVac) | Pork, red and processed meats, non-gassing cheese | 40 µm film with EVOH barrier | Up to 60% less plastic than thermoforming | Needs shrink and vacuum chamber equipment |
| Vacuum skin on tray (Darfresh on Tray) | Case-ready proteins | 80 µm PE-sealant top web on a mono-PP, mono-PET or board support | Zero skeleton film scrap | Still has a tray |
| Skin pack for meals (Simple Steps) | Chilled and frozen ready meals | Skin top web on PP bottom web or pre-made tray | No weight figure published | Tray stays; film must survive microwave and pasteurisation |
Where each format fits
AutoWrap Lite is the cheese specialist. The interpack 2026 exhibitor listing says it suits non-active, gassing cheeses and hard or semi-hard chunks of 80 to 1,000 g, with shelf life up to 120 days. Speed is quoted at 45 to 90 packs per minute, and the Packaging Europe Spotlight puts shelf life at 45 to 120 days under validated conditions. A shelf-life range that wide tells you it depends on cheese type, so it needs your own validation.
PrimeVac is a shrink bag rollstock for in-line bag making. Sealed Air specifies 40 µm, an EVOH barrier, 56% shrink (longitudinal and transverse), no external slip agents, and surface pasteurisation up to 85°C for 10 minutes or 92°C for 5 minutes. The supplier states it uses 60% less plastic than thermoforming.
Darfresh on Tray keeps a tray but changes the lid. The supplier says traditional skin pack machines produce 30 to 40% scrap, while its tray-sealing version uses all of the film. Its 80 µm polyethylene-sealant top webs are listed as compatible with mono-PP and mono-PET trays or board.
For ready meals, the Simple Steps page describes a vacuum skin film over semi-rigid or rigid PP bottom webs or pre-made trays. The supplier says the film allows HPP or thermal post-pasteurisation, and that the pack can be sold fresh or frozen.
What the film data does and doesn’t tell you
The supplier pages give thicknesses, shrink and pasteurisation limits, but I found no published oxygen transmission rates for these films. A barrier claim needs a number with its conditions, for example OTR at 23°C and a stated RH under ASTM D3985. Ask for the data sheet and the test method before you compare an EVOH shrink film with a PE skin web.
Thin film also shifts risk from the pack to the line. The Spotlight says performance has to hold as materials get thinner and lighter, and Sealed Air’s own argument for PrimeVac is that film, loading and chamber machine are designed as one system. That is a reasonable point for a supplier to make, and it means a film trial on your existing machine may not reproduce the supplier’s results. If you need to turn a film width and gauge into roll yield, the film roll tool below does the arithmetic.
Free tool: Film roll calculator converts gauge and roll size into length and yield, which helps when a thinner web changes your roll changes per shift.
Recycling claims and what sits behind them
AutoWrap Lite’s film is reported to hold an 87% recyclability certification from Cyclos-HTP, per the Packaging Insights piece quoted above. Sealed Air’s breathable shrink bags are described as approved for RIC 4 labelling, with the supplier’s own qualifier that PE is recyclable where facilities exist. Both claims depend on the collection route, and flexible PE collection is patchy.
The tray-based formats have a different issue: a mono-PP or mono-PET tray with a PE-sealant lid is only as recyclable as the sorting stream that receives it. The EU’s packaging regulation (PPWR) sets recyclability and reduction rules that apply to food packs; check the current text and the detail at ppwreu.org rather than relying on a supplier summary.
Limits worth knowing before you ask for a trial
Every weight figure here is a mass comparison, not a life-cycle result. The Spotlight itself says the BDF film’s 60% reduction is against selected thick laminates or thermoforming materials, from internal pack-weight analyses. That tells you which baseline the supplier chose, and your current pack may be lighter or heavier than it.
The format also depends on product behaviour. Gassing cheeses are outside AutoWrap Lite’s stated scope, and a soft film pack gives less crush protection than a formed tray in a mixed case or a shipper. Retail display changes too, since a skin or wrap pack shows the product shape rather than a printed tray.
What this means for you
- R&D: Define your baseline in grams per 100 g of product before any supplier meeting, using your current pack and portion size. Ask for the reference pack behind every reduction claim.
- Quality: Request OTR and WVTR with the test temperature and humidity, plus the seal-strength method. Plan your own shelf-life study for each cheese or meal, since the 45 to 120 day range is a validated range for the supplier’s conditions, not yours.
- Procurement: Ask for a quote on the whole system: film, machine, and any tray, rather than film per kilogram. Where a format change needs a new machine, thinner film can’t be judged on film price alone.
- Design: Check how the pack looks on shelf and in a case, and whether the film is printable to your needs. For meals, confirm microwave and pasteurisation limits against the data sheet.
- Sustainability: Check which recycling route actually takes the pack in each market. A certification score and a label are two separate things.
Free tool: Lightweighting calculator turns a per-pack weight change into material saved per year, using your own volumes.
Sources
- Packaging Europe: Meeting the growing demands of food packaging: Where performance meets responsibility
- Packaging Insights: Sealed Air, Coveris and Dole rethink food packaging to cut waste and carbon
- Packaging Europe: Sealed Air and Bradbury’s Cheese target plastic reduction with new wrapping system
- Sealed Air: AutoWrap Lite soft vacuum system
- interpack 2026: CRYOVAC AutoWrap Lite exhibitor listing
- Sealed Air: Shrinkable Rollstock PrimeVac
- Sealed Air: Darfresh on Tray
- Sealed Air: Simple Steps meal packaging
- Sealed Air: Recycle-Ready Breathable Shrink Bags
- PPWR EU: packaging regulation reference
Header image: illustration, AI-generated.

