Quick answer: Estimate the empty-box strength from board ECT, caliper and box perimeter with the simplified McKee formula, then divide by a safety factor that reflects storage time, humidity and pallet pattern. Confirm the result with an ASTM D642 (or ISO 12048) compression test on conditioned, fully assembled boxes. The estimate is a starting point; the published safety factors range from about 2 to 7, so the choice of factor matters more than the third decimal of the formula.
This sheet is for anyone who has to say “this case will survive a five-high stack” and defend it. It covers what the numbers measure, how to calculate and test them, and where published studies say strength goes missing between the lab and the warehouse. All figures below come from standards pages, test-lab and supplier guidance, and academic work, named where used. None of it is first-hand testing, and the numbers are typical values, not specifications for your board.
What ECT, BCT and caliper each tell you
ECT (edge crush test) is a board property. ISO 3037 specifies a non-waxed edge method for edgewise crush resistance of corrugated fibreboard, with the force applied along the flute axis. ECT is the maximum force divided by sample width, so a 2 inch strip that fails at 64 lbf gives 32 lb/in. In SI that is about 5.6 kN/m (using 1 lb/in = 0.1751 kN/m, the conversion quoted by OpsCalculators).
BCT (box compression test) is a pack property. The matching standards are ISO 12048 and TAPPI T 804 for BCT, against ISO 3037 and TAPPI T 811 for ECT. ASTM D642 is closely related to TAPPI T804.
Caliper is the combined board thickness, and it enters the McKee formula under a square root. Use the measured value for your actual board, not the nominal flute thickness from a catalogue.
One conditioning detail changes everything. One test-equipment maker states ISO 3037 conditioning as 23 ± 1 °C and 50 ± 2 % RH, tighter than the usual lab atmosphere because ECT falls sharply with moisture. If two suppliers quote ECT from labs that don’t hold this atmosphere, their numbers aren’t comparable.
Estimating BCT with the McKee formula
The McKee formula, first published in 1963, is still in everyday use to turn board strength into a box-strength estimate. The simplified form is BCT = 5.87 × ECT × √(caliper × perimeter), with BCT in pounds, ECT in lb/in, caliper and perimeter in inches. The original paper is McKee, Gander and Wachuta, “Compression Strength Formula for Corrugated Boxes”, Paperboard Packaging, 1963.
Steps, in order:
- Get the combined-board ECT from the board supplier’s certificate or from your own ISO 3037 / TAPPI T 811 result. Don’t substitute Mullen burst; the formula requires ECT, not Mullen.
- Measure combined-board caliper on the finished sheet, after the corrugator and converting, not before.
- Calculate perimeter as 2 × (length + width) of the box.
- Multiply: 5.87 × ECT × √(caliper × perimeter).
- Convert units last. 1 lb is 4.448 N.
A worked example, using the dimensions from a published illustration: 32 ECT board, 0.200 in thick, 12 in × 9 in box (perimeter 42 in), giving roughly 545 lb. In SI that is a 5.6 kN/m board, 5.1 mm caliper, a box of about 305 × 229 mm, and a BCT near 2,420 N (my conversion of the published figure).
Now the step most worksheets skip. Divide by a safety factor. With a factor of 4, the allowable load is about 605 N, roughly 62 kg-force. If a filled case weighs 8 kg, seven cases above the bottom one is 56 kg, so an eight-high column passes on this arithmetic and nine fails. Check the numbers for your own board in our box compression calculator.
Know what the formula doesn’t cover. Most estimations don’t relate well to other box orientations, other box styles, or filled boxes. Bag-in-box packs and many semisolids develop hydrostatic forces that reduce compression strength. Rigid, full contents can add support instead, which is why a physical test on the filled pack beats the formula whenever the stack is critical.
Running the compression test: ASTM D642 in practice
ASTM D642 covers compression tests on shipping containers such as boxes and drums, or their components, with or without contents. It can measure resistance to loads applied to faces, to diagonally opposite edges, or to corners. Check the current text of the edition you cite; D642-20 is the edition listed by one lab-equipment supplier.
- Build the specimen as production does. Specimens should be the full container, prepared the way it will be packed and shipped. Same closure method, same tape or glue, same inserts.
- Record what the report needs. That includes inside dimensions, a description of contents and gross filled weight, and fastener spacing, size and type.
- Condition for the full period. Hold the test atmosphere you will quote; conditioning to standard temperature and humidity is important.
- Centre the box on the lower platen and bring the platens into contact with a preload, then apply load at the specified rate until failure or a specified load. One supplier quotes 12.5 mm/min. Fixed or swivel platens are both allowed. Name which one you used, because results can differ.
- Test enough boxes. The guidance from one equipment maker is five or more samples, averaged. Report the minimum too, not only the mean, since the weakest box is the one on the bottom of the pallet.
- Record peak load and deflection. Typical outputs are load at critical deformation points, maximum load and maximum deformation.
A lab BCT is a peak load on a short ramp. For constant-load storage questions, the standard itself points to Test Method D4577.
Why the lab number is not the warehouse number
Lab BCT is short-term, dry and aligned. Real stacks lose strength over time, in humidity, with vibration and with misaligned corners, which is the reason for a safety factor.
Humidity is the biggest single driver, and published figures vary with the source. Pkg Solutions puts the loss at about 50% when relative humidity moves from 40% to 90%. PaperIndex cites Fibre Box Association data for a 50% to 60% loss once board reaches equilibrium at 90% RH. Packwire’s calculator guide gives a retained strength of about 70% at 80% RH and about 55% at 90%. Cold rooms are worse: it cites a 2019 Stellenbosch University study that measured a 31% loss at about 2 °C and 85% RH. That is a secondary citation, so check the original paper before using it in a specification.
Time under load matters as well. Reduced stiffness may not show until the box has been loaded for an extended period. That is the case for choosing the factor by storage duration.
| Source | Factor (×) | Situation it describes |
|---|---|---|
| Cubit Packaging ECT guide | 2.0 | Short-term, 1 to 7 days |
| Cubit Packaging ECT guide | 2.5 | Medium-term, 7 to 30 days |
| Cubit Packaging ECT guide | 4.0 | Long-term, over 30 days |
| Pkg Solutions guidance | 3 to 7 | Typical design range; 6 or 7 for world-wide distribution with storage of up to nine months |
| Packagingtools.io calculator FAQ | about 3 to 6 or 7 | Short parcel up to long-term or ocean export |
| Lansbox guide | 1.5 to 3 | Long-term or humid storage (it applies this as an environmental factor) |
The spread is wide because the sources define the factor differently. Some fold humidity, creep and pallet pattern into one number; others apply separate derates. Pick one convention, write it into the spec, and don’t multiply derates that already sit inside the factor. Treat the table as published rules of thumb, not requirements.
Pallet losses: overhang, pattern and deck gaps
The pallet pattern can cost as much as the weather. In peer-reviewed tests summarised by Korpack, interlocked patterns lost 4 to 35 percent versus column stacking, and interlock plus overhang cost up to 34 percent on individual boxes. The same summary gives about 25 percent average loss from three-high palletisation and 13 percent average loss from a 25.4 mm overhang. Those tests were run per ASTM D642 on four box sizes, with CHEP and GMA pallets.
Other sources quote bigger numbers. Great Lakes Box says interlocking can destroy up to 50% of strength and deck-board gaps up to 15%. These are trade-guidance figures, so the loss range for your own box, pallet and pattern should come from your own D642 test on a unit load.

The chart mixes sources and test set-ups, so the bars aren’t additive and shouldn’t be summed into one derate. It shows why a flat 2× can be too thin for a humid, interlocked, overhanging load.
Column stacking keeps the same footprint on each layer, so corners sit on corners. The catch is lateral stability: column stacking needs stretch wrap or strapping. To check the layer count and truck fill for a pattern, use the pallet load calculator.
Troubleshooting: bottom boxes crushing
| Symptom | Likely cause | What to check or change |
|---|---|---|
| Bottom layer bulges and collapses after days or weeks | Static load plus creep; factor too low for storage time | Re-run the sum with a factor for the real storage time; shorten the stack |
| Failures concentrated in humid season or cold store | Board moisture above the 50% RH test condition | Compare against the humidity figures above; ask your board supplier about moisture-resistant liners or coatings |
| Crushed edges on boxes that overhang the pallet | Overhang removes corner support | Resize the case or pattern to the pallet footprint; use a plywood or corrugated deck sheet if edges fall between slats |
| Lab BCT passes, pallet fails | Interlocked pattern, deck-board gaps or misaligned layers | Test a unit load per ASTM D642, not a single box |
| ECT on certificate does not match your own result | Different conditioning, washboarding or poor specimen cuts | Confirm 23 °C and 50% RH; check specimen edges to ISO 3037 |
| Formula predicts well, filled box underperforms | Contents add hydrostatic load or sag; McKee covers empty boxes | Test the filled pack; add dividers or change the fill |
On the ECT row: the ISO 3037 text notes that washboarding of corrugated board can severely affect test values. Specimens should also show no visible light under the cut edge when placed against a flat surface.
Common mistakes
- Using a lab BCT as a working load. It’s a peak value at one atmosphere, on one box, aligned.
- Quoting ECT without conditions. A number with no temperature, RH and standard behind it can’t be compared with another.
- Mixing units. The simplified formula is in lb/in and inches. If you work in kN/m and mm, convert before multiplying, or use the unit converter.
- Using nominal caliper. Crushed or washboarded board is thinner than the catalogue says.
- Stacking safety factors. Applying a storage-time factor and then separate humidity and pallet derates counts the same loss twice.
- Testing one box. Five or more samples, with the minimum reported, is the guidance quoted above.
- Testing empty when the pack ships full (or the reverse), without saying which.
What this means for you
Start the spec with the use case: storage days, worst-case RH, pallet pattern and stack height. Pick a safety factor convention from the table, cite the source, and write down what it already includes.
Calculate the required BCT from the bottom-box load, solve the McKee formula for ECT, and ask board suppliers for a quote against that ECT, caliper and ISO 3037 conditioning. Then confirm with ASTM D642 on filled, closed boxes, or on a unit load if pallet pattern is in play.
If overhang or interlocking is unavoidable, test that exact pattern. If the pack will see cold rooms or sea freight, ask the board supplier about moisture-resistant options and look at the original studies rather than the calculator summaries. Packaging law such as PPWR also touches paper-based packs; for that, check the current text at ppwreu.org.
Sources
- ISO: ISO 3037:2022 Corrugated fibreboard, edgewise crush resistance (non-waxed edge method)
- ISO 3037:2022 preview sample (iTeh)
- Dak System: ISO 3037 edge crush test
- Dak System: ASTM D642 box compression test
- iTeh: ASTM D642 scope
- TestResources: ASTM D642 test equipment and procedure
- Keystone Compliance: ASTM D642 compressive resistance testing
- ADMET: ASTM D642 shipping container compression testing
- ZwickRoell: Edge crush test (ECT)
- Korpack: Why your boxes crush when you stack them
- Presto Group: Edge crush test guide
- OpsCalculators: Box compression strength calculator
- Wikipedia: Edge crush test
- EngiCalcsHub: Box compression guide
- Pkg Solutions: More about compression
- Cubit Packaging: ECT calculator and cheat sheet
- Packagingtools.io: Corrugated strength calculator
- Lansbox: How to calculate compressive strength of corrugated boxes
- Packwire: Box stacking strength calculator
- PaperIndex: How humidity changes corrugated box stack planning
- Wikipedia: Container compression test
- Korpack: Choosing pallet patterns
- Cal Poly: Effect of palletized box offset on compression strength
- Great Lakes Box: Storing and handling guidelines
- Tyoga Container: The importance of proper palletization
- Palletizing Robot Factory: Pallet stacking patterns
Values are typical figures from the cited sources. Real performance depends on the grade, the test method and the conditions. Check the supplier's data sheet and test your own structure.

